Releases: speeduino/Ardu-Stim
Ardu-Stim V1.2.1
Ardu-Stim V1.2.0
What's Changed ❓
- RPM Scaling on the '36-2 with Cam' pattern has been fixed
- Fix for the 2 cylinder compression wave being incorrect (Was showing as 4 cylinder)
- Multiple GUI fixes
- Prevent possibility of multiple RPM requests being made simultaneously. This could cause the RPM read frequency to halve after a few hours operation
Ardu-Stim V1.1.0
What's Changed
- Add compression wave options for different angles and dynamic amplitude
- Add 36-2 with 1 cam by @ggurov in #75
- Fix a bug where the wheel pattern would not save correctly
- Fix an issue where there was the incorrect number of compression waves if a 720 degree wheel was selected.
- Perform a check on connection to make sure the firmware version matches the GUI
Contributors
Assets 5
Ardu-Stim V1.0.0
After many years of being only for developers, Ardu-Stim is finally getting a v1.0.0 release! 🎉
It's hard to know where to begin in describing this release as there has been a HUGE number of changes made since the Alpha was released a few years ago.
The firmware for the board itself has matured and been cleaned up significantly. It's now in a very good position for new features to be added and there has been a large amount of resources freed up for Nano boards. Useful features such as varying speed on the ranged RPM sweep and low RPM compression waves demonstrate the flexibility of the system now.
The GUI, whilst far from perfect still, is now reasonably tidy on Windows, Mac and linux. The firmware upload has now been fixed on all platforms also, making it easier to get up and running.
Major Features 🏎️
- 3 RPM Modes:
- Potentiometer
- Fixed RPM
- Ranged sweep (With variable range and speed)
- Compression 'waves' at low RPM
- Built-in uploading of firmware to board
Bug Fixes 🐞
Too many to mention!
Wheel Patterns ⚙️
- 4 cylinder dizzy
- 6 cylinder dizzy
- 8 cylinder dizzy
- 60-2 crank only
- 60-2 crank and cam
- 60-2 crank and 'half moon' cam
- 36-1 crank only
- 24-1 crank only
- 4-1 crank wheel with cam
- 8-1 crank only (R6)
- 6-1 crank with cam
- 12-1 crank with cam
- 40-1 crank only (Ford V10)
- Distributor style 4 cyl 50deg off, 40 deg on
- Odd fire 90 deg pattern 0 and 135 pulses
- GM OptiSpark LT1 360 and 8
- 12-3 oddball
- 36-2-2-2 H4 Crank only
- 36-2-2-2 H6 Crank only
- 36-2-2-2 Crank and cam
- GM 4200 crank wheel
- Mazda FE3 36-1 with cam
- Mitsubishi 6g72 with cam
- Buell Oddfire CAM wheel
- GM LS1 crank and cam
- GM 58x crank and 4x cam
- Odd Lotus 36-1-1-1-1 flywheel
- Honda RC51 with cam
- 36-1 crank with 2nd trigger on teeth 33-34
- Chrysler NGC 36+2-2 crank, NGC 4-cyl cam
- Chrysler NGC 36-2+2 crank, NGC 6-cyl cam
- Chrysler NGC 36-2+2 crank, NGC 8-cyl cam
- Weber-Marelli 8 crank+2 cam pattern
- Fiat 1.8 16V crank and cam
- Nissan 360 CAS with 6 slots
- Mazda CAS 24-2 with single pulse outer ring
- Yamaha 2002-03 R1 8 even-tooth crank with 1 tooth cam
- GM 4 even-tooth crank with 1 tooth cam
- GM 6 even-tooth crank with 1 tooth cam
- GM 8 even-tooth crank with 1 tooth cam
- Volvo d12[acd] crank with 7 tooth cam
- Mazda 36-2-2-2 with 6 tooth cam
- Mitsubishi 4g63 aka 4/2 crank and cam
- Audi 135 tooth crank and cam
- Honda D17 Crank (12+1)
- Mazda 323 AU version
- Daihatsu 3+1 distributor (3 cylinders)
- Miata 99-05
- 12/1 (12 crank with cam)
- 24/1 (24 crank with cam)
- Subaru 6/7 crank and cam
- GM 7X
- DSM 420a
- Ford ST170
- Mitsubishi 3A92
- Toyota 4AGE
- Toyota 4AGZE
- Suzuki DRZ400
- Jeep 2000
- BMW N20
- Dodge Viper V10 1996-2002
V1.0.0 Beta 2
2nd beta prior to the v1.0 release.
- Faster loading
- Adds compression waves function
- Multiple fixes for Windows
- Fixes that could cause lockup on blank arduino
- Background improvements to memory and config layout
V1.0.0 Beta 1
Too many changes to list since the last Alpha version. IN short though:
- Many new wheel patterns added
- Uploading of firmware should now work for Arduino Nano boards (Maybe Uno?)
- Sweep function now works
- UI correctly displays the config that is saved on the board
- Support for 2 cam signals rather than 1 (3 total signals generated)
- MANY bugs fixed
- Most libraries updated
This is a beta release to allow people to test this ahead of an upcoming release. There will be at least 1 more beta prior to a final release.
Alpha 2 test release
- Add ability to burn firmware through UI, no need to compile this (Arduino nano 328 only)
- Add saving of settings on the arduino so that they persist between restarts
- Add scope style view in addition to wheel view
- Multiple bug fixes and small improvements
Instructions
You MUST install the new firmware that comes along with this release. It will not work if your Arduino has an earlier firmware on it. If you are using an Arduino Uno or Nano, simply start the application, select the correct port and press the button to upload the firmware. After that press Connect.
You will only have to do the firmware upload once for this version.
Alpha 1 test release
First mostly working test release.
Known Issues:
- Sweep RPM does not work
- Alignment of RPM readout and actual pulse signal may not match
- Slight visual glitches on some patterns
- No icon
Test release only
0.0.2 Add updater