Implement Negative Command Queue Tests #2010
Conversation
ahesham-arm
force-pushed
the
negative_command_queue_tests
branch
3 times, most recently
from
2c71436
to
1e798fa
Compare
| err = clSetDefaultDeviceCommandQueue(nullptr, deviceID, queue); | ||
| test_failure_error_ret( | ||
| err, CL_INVALID_CONTEXT, | ||
| "clSetDefaultDeviceCommandQueue should return CL_INVALID_CONTEXT when " | ||
| "\"context is not a valid context\" using a nullptr", | ||
| TEST_FAIL); |
There was a problem hiding this comment.
I think a lot of these cases need to be updated to allow for CL_INVALID_OPERATION as well, when the passed-in device ID does not support a replaceable default on-device queue. This can happen if the device is a pre-OpenCL 2.0 device, or if the device is an OpenCL 3.0 device that does not support a replaceable default.
| return TEST_PASS; | ||
| } | ||
|
|
||
| int test_negative_set_command_queue_property(cl_device_id deviceID, |
There was a problem hiding this comment.
I think clSetCommandQueueProperty needs to handle the cases when the device is newer than OpenCL 1.0 and hence can return CL_INVALID_OPERATION.
See discussion and the latest changes in the now-merged #1182.
| "CL_INVALID_VALUE when: \"values specified in " | ||
| "properties are not valid\" using a queue size " | ||
| "greater than CL_DEVICE_QUEUE_ON_DEVICE_MAX_SIZE", | ||
| TEST_FAIL); |
There was a problem hiding this comment.
Spec:
CL_INVALID_VALUE if values specified in properties are not valid.
CL_INVALID_QUEUE_PROPERTIES if values specified in properties are valid but are not supported by the device.
Looks like this could equally be interpreted as a case for "CL_INVALID_QUEUE_PROPERTIES" since the size itself is "not supported by the device" having exceeded CL_DEVICE_QUEUE_ON_DEVICE_MAX_SIZE.
Would like to discuss this in the next call.
There was a problem hiding this comment.
Agreed on 8/27 to accept either error code (CL_INVALID_VALUE or CL_INVALID_QUEUE_PROPERTIES) for this case. Arm will make this fix in a subsequent patch.
There was a problem hiding this comment.
@ahesham-arm Looks like the PR will need updating to address the request above.
|
Removing the "focused review" label until the comments above have been addressed. |
ahesham-arm
force-pushed
the
negative_command_queue_tests
branch
from
1e798fa
to
c87e9e3
Compare
Implement negative tests for the following functions:
- clCreateCommandQueueWithProperties
- clCreateCommandQueue
- clSetDefaultDeviceCommandQueue
- clRetainCommandQueue
- clReleaseCommandQueue
- clGetCommandQueueInfo
- clSetCommandQueueProperties
Signed-off-by: Chetankumar Mistry <[email protected]>
Signed-off-by: Ahmed Hesham <[email protected]>
ahesham-arm
force-pushed
the
negative_command_queue_tests
branch
from
c87e9e3
to
fc5b5c0
Compare
| "CL_INVALID_VALUE or CL_INVALID_QUEUE_PROPERTIES when: " | ||
| "\"values specified in properties are not valid\" using a " | ||
| "queue size greather than " | ||
| "CL_DEVICE_QUEUE_ON_DEVICE_MAX_SIZE"); |
There was a problem hiding this comment.
If error occurs, it prints
negative_create_command_queue_with_properties...
clCreateCommandQueueWithProperties should return CL_INVALID_VALUE or CL_INVALID_QUEUE_PROPERTIES when: "values specified in properties are not valid" using a queue size greather than CL_DEVICE_QUEUE_ON_DEVICE_MAX_SIZEnegative_create_command_queue_with_properties FAILED
can we add "\n" or "." to split the 2 sentences? Same comments for other log_error call.
Implement negative tests for the following functions: