Skip to content

Latest commit

 

History

History
165 lines (109 loc) · 5.71 KB

README.arm.md

File metadata and controls

165 lines (109 loc) · 5.71 KB
Raw

Julia on ARM (Linux)

Julia fully supports ARMv8 (AArch64) processors, and supports ARMv7 and ARMv6 (AArch32) with some caveats. This file provides general guidelines for compilation, in addition to instructions for specific devices.

A list of known issues for ARM is available. If you encounter difficulties, please create an issue including the output from cat /proc/cpuinfo.

Building Julia

In most cases, Julia can be successfully built by following the platform independent build instructions.

Build dependencies

We recommend using at least Ubuntu 14.04 and gcc 4.8, which is part of the standard build-essentials.

In case the build is failing on one of the dependent libraries, one can install various system libraries instead of building them, by adding the following lines in Make.user:

override USE_SYSTEM_BLAS=1
override USE_SYSTEM_LAPACK=1
override USE_SYSTEM_LIBM=1
override USE_SYSTEM_GMP=1
override USE_SYSTEM_MPFR=1
override USE_SYSTEM_ARPACK=1

The following command will install all the necessary libraries on Ubuntu:

sudo apt-get install libblas3gf liblapack3gf libarpack2 libgmp3-dev \
                     libmpfr-dev libblas-dev liblapack-dev cmake gcc-4.8 \
                     g++-4.8 gfortran libgfortran3 m4 libedit-dev

If you run into issues building LLVM, see these notes.

32-bit (ARMv6, ARMv7)

Julia has been successfully compiled on several variants of the following ARMv6 & ARMv7 devices:

  • ARMv7 / Cortex A15 Samsung Chromebooks running Ubuntu Linux under Crouton;
  • Raspberry Pi.
  • Odroid.

Julia requires at least the armv6 and vfpv2 instruction sets. It's recommended to use armv7-a. armv5 or soft float are not supported.

Binaries

Nightly builds are available for ARMv7-A.

Device specific instructions

Raspberry Pi 1 / Raspberry Pi Zero

The type of ARM CPU used in the Raspberry Pi is not detected by LLVM. Explicitly set the CPU target by adding the following to Make.user:

JULIA_CPU_TARGET=arm1176jzf-s

It is preferable to use various system provided dependencies on ARMv6 as described in Build Dependencies.

To complete the build, you may need to increase the swap file size. To do so, edit /etc/dphys-swapfile, changing the line:

CONF_SWAPSIZE=100

to:

CONF_SWAPSIZE=512

before restarting the swapfile service:

sudo /etc/init.d/dphys-swapfile stop
sudo /etc/init.d/dphys-swapfile start

Raspberry Pi 2

The type of ARM CPU used in the Raspberry Pi 2 is not detected by LLVM. Explicitly set the CPU target by adding the following to Make.user:

JULIA_CPU_TARGET=cortex-a7

Depending on the exact compiler and distribution, there might be a build failure due to unsupported inline assembly. In that case, add MARCH=armv7-a to Make.user.

If building LLVM fails, you can download binaries from the LLVM website:

  1. Download the [LLVM 3.9.0 binaries for ARMv7a] (http://llvm.org/releases/3.9.0/clang+llvm-3.9.0-armv7a-linux-gnueabihf.tar.xz) and extract them in a local directory.

  2. Add the following to Make.user (adjusting the path to the llvm-config binary):

    override USE_SYSTEM_LLVM=1
LLVM_CONFIG=${EXTRACTED_LOCATION}/bin/llvm-config

Please do let us know if you had to download a pre-built LLVM in #10235.

Chromebook

On Chromebooks, you have to first install Crouton. If you do not have an Ubuntu chroot running on your Chromebook using Crouton, you can do so by following these tutorials.

These tutorials will end up installing Ubuntu 12.04, and you have to upgrade to Ubuntu 14.04, or install Ubuntu 14.04 from scratch by finding appropriate crouton help.

Scaleway cloud hosted ARM servers

On the current Scaleway ARM servers, the Julia build works out of the box.

AArch64 (ARMv8)

Julia has been successfully built on the following ARMv8 devices:

Compilation on ARMv8-A requires that Make.user is configured as follows:

MARCH=armv8-a

Device specific instructions

nVidia Jetson TX2

Julia builds and runs on the nVidia Jetson TX2 platform with minimal configuration changes.

After configuring Make.user as per the AArch64 instructions in this document, follow the general build instructions. The majority of the build dependencies specified in the instructions are installed by the default configuration flashed by Jetpack 3.0. The remaining tools can be installed by issuing the following command:

sudo apt-get install gfortran wget cmake

A full parallel build, including LLVM, will complete in around two hours. All tests pass and CUDA functionality is available through, e.g., CUDAdrv.