direwolf.conf

#############################################################
#                                                           #
#               direwolf配置文件模板                          #
#                                                           #
#############################################################

# 树莓派USB声卡
ADEVICE  plughw:1,0
#


# Logging Use period (“.”) for the current working directory.
# 日志记录目录，. 表示当前目录
LOGDIR .

TXDELAY 30

# 使用通道0
CHANNEL 0
# 呼号配置
MYCALL BH8VJH-10

#
# Pick a suitable modem speed based on your situation.
#	1200 	Most common for VHF/UHF.  Default if not specified.
#	300	Low speed for HF SSB.
#	9600	High speed - Can't use Microphone and Speaker connections.
#
# In the simplest form, just specify the speed.
#

# 使用波特率1200 的afsk调制解调(一般情况，U/V段使用1200，300使用在短波上，9600用于传图片)
MODEM 1200
#MODEM 300
#MODEM 9600

#
# These are the defaults should be fine for most cases.  In special situations,
# you might want to specify different AFSK tones or the baseband mode which does
# not use AFSK.
#
#MODEM 1200 1200:2200
#MODEM 300  1600:1800
#MODEM 9600 0:0
#
#
# On HF SSB, you might want to use multiple demodulators on slightly different
# frequencies to compensate for stations off frequency.  Here we have 7 different
# demodulators at 30 Hz intervals.  This takes a lot of CPU power so you will
# probably need to reduce the audio sampling rate with the /n option.

#MODEM 300 1600:1800 7@30 /4


#
# Uncomment line below to enable the DTMF decoder for this channel.
#

#DTMF

#
# If not using a VOX circuit, the transmitter Push to Talk (PTT)
# control is usually wired to a serial port with a suitable interface circuit.
# DON'T connect it directly!
#
# For the PTT command, specify the device and either RTS or DTR.
# RTS or DTR may be preceded by "-" to invert the signal.
# Both can be used for interfaces that want them driven with opposite polarity.
#

#PTT COM1 RTS
#PTT COM1 RTS -DTR

# The Data Carrier Detect (DCD) signal can be sent to the same places
# as the PTT signal.  This could be used to light up an LED like a normal TNC.

#DCD COM1 -DTR

## 树莓派GPIO 25脚控制PTT ################
PTT GPIO 25

#############################################################
#                                                           #
#               CHANNEL 1 PROPERTIES                        #
#                                                           #
#############################################################

#CHANNEL 1

#
# Specify MYCALL, MODEM, PTT, etc. configuration items for
# CHANNEL 1.   Repeat for any other channels.


#############################################################
#                                                           #
#               TEXT TO SPEECH COMMAND FILE                 #
#                                                           #
#############################################################



#############################################################
#                                                           #
#               VIRTUAL TNC SERVER PROPERTIES               #
#                                                           #
#############################################################

#
# Dire Wolf acts as a virtual TNC and can communicate with
# client applications by different protocols:
#
#	- the "AGW TCPIP Socket Interface" - default port 8000
#	- KISS protocol over TCP socket - default port 8001
#

# 虚拟TNC端口配置
AGWPORT 8000
KISSPORT 8001

#
# It is sometimes possible to recover frames with a bad FCS.
# This applies to all channels.
#
#	0  [NONE] - Don't try to repair.
#	1  [SINGLE] - Attempt to fix single bit error.  (default)
#	2  [DOUBLE] - Also attempt to fix two adjacent bits.
#	... see User Guide for more values and in-depth discussion.
#

#FIX_BITS 0

#
#############################################################
#                                                           #
#               BEACONING PROPERTIES                        #
#                                                           #
#############################################################


#
# Beaconing is configured with these two commands:
#
#	PBEACON		- for a position report (usually yourself)
#	OBEACON		- for an object report (usually some other entity)
#
# Each has a series of keywords and values for options.
# See User Guide for details.
#
# Example:
#
# This results in a broadcast once every 10 minutes.
# Every half hour, it can travel via two digipeater hops.
# The others are kept local.
#
# 信标配置，需要具体修改经纬度坐标
PBEACON delay=10 every=30 overlay=S symbol="digi" lat=42^37.14N long=071^20.83W power=50 height=20 gain=4 comment="Chelmsford MA"

#PBEACON delay=21 every=30 overlay=S symbol="digi" lat=42^37.14N long=071^20.83W power=50 height=20 gain=4 comment="Chelmsford MA"


# With UTM coordinates instead of latitude and longitude.

#PBEACON delay=1 every=10 overlay=S symbol="digi" zone=19T easting=307477 northing=4720178


#
# When the destination field is set to "SPEECH" the information part is
# converted to speech rather than transmitted as a data frame.
#

#CBEACON dest="SPEECH" info="Club meeting tonight at 7 pm."

# Similar for Morse code.  If SSID is specified, it is multiplied
# by 2 to get speed in words per minute (WPM).

#CBEACON dest="BH8VJH" info="BH8VJH-15"
#
# Modify for your particular situation before removing
# the # comment character from the beginning of appropriate lines above.
#


#############################################################
#                                                           #
#               DIGIPEATER PROPERTIES                       #
#                                                           #
#############################################################

#
# For most common situations, use something like this by removing
# the "#" from the beginning of the line below.
#

# 数据中继规则配置，有这项配置才能够启动APRS数字中继功能
DIGIPEAT 0 0 ^WIDE[3-7]-[1-7]$|^TEST$ ^WIDE[12]-[12]$ TRACE

# See User Guide for more explanation of what this means and how
# it can be customized for your particular needs.

# Filtering can be used to limit was is digipeated.
# For example, only weather weather reports, received on channel 0,
# will be retransmitted on channel 1.
#

#FILTER 0 1 t/wn


#############################################################
#                                                           #
#               INTERNET GATEWAY                            #
#                                                           #
#############################################################

# First you need to specify the name of a Tier 2 server.
# The current preferred way is to use one of these regional rotate addresses:
#
# 指定APRS-IS服务器
IGSERVER s.aprs.cn


# You also need to specify your login name and passcode.
# Contact the author if you can't figure out how to generate the passcode.
# 登录信息，NOCALL换成你的呼号 这里xxx四aprs验证码
IGLOGIN NOCALL xxxx

# That's all you need for a receive only IGate which relays
# messages from the local radio channel to the global servers.

# Some might want to send an IGate client position directly to a server
# without sending it over the air and relying on someone else to
# forward it to an IGate server.  This is done by using sendto=IG rather
# than a radio channel number. Overlay R for receive only, T for two way.

#PBEACON sendto=IG delay=0:01 every=10:00 symbol="igate" overlay=T lat=25^2.33N long=102^43.62W
#PBEACON sendto=IG delay=0:30 every=60:00 symbol="igate" overlay=T lat=42^37.14N long=071^20.83W


# To relay messages from the Internet to radio, you need to add
# one more option with the transmit channel number and a VIA path.

IGTXVIA 0 WIDE1-1
IGTXVIA 0
# You might want to apply a filter for what packets will be obtained from the server.
# Read about filters here:  http://www.aprs-is.net/javaprsfilter.aspx
# Example, positions and objects within 50 km of my location:

# 范围50公里 
#IGFILTER m/50

#服务器端过滤呼号
IGFILTER b/BH8SEL*/BG8SPA*
# 转发过滤
FILTER IG 0 b/BH8SEL*



# That is known as a server-side filter.  It is processed by the IGate server.
# You can also apply local filtering to limit what will be transmitted on the
# RF side.  For example, transmit only "messages" on channel 0 and weather
# reports on channel 1.

#FILTER IG 0 t/m
#FILTER IG 1 t/wn

# Finally, we don't want to flood the radio channel.
# The IGate function will limit the number of packets transmitted
# during 1 minute and 5 minute intervals.   If a limit would
# be exceeded, the packet is dropped and message is displayed in red.
# 发送限制，1分钟内6条，5分钟内10条
IGTXLIMIT 6 10

#############################################################
#                                                           #
#               APRStt GATEWAY                              #
#                                                           #
#############################################################

#
# Dire Wolf can receive DTMF (commonly known as Touch Tone)
# messages and convert them to packet objects.
#
# See separate "APRStt-Implementation-Notes" document for details.
#

#
# Sample gateway configuration based on:
#
#	http://www.aprs.org/aprstt/aprstt-coding24.txt
#	http://www.aprs.org/aprs-jamboree-2013.html
#

# Define specific points.

TTPOINT  B01  37^55.37N  81^7.86W
TTPOINT  B7495088  42.605237  -71.34456
TTPOINT  B934  42.605237  -71.34456

TTPOINT B901  42.661279  -71.364452
TTPOINT B902  42.660411  -71.364419
TTPOINT B903  42.659046  -71.364452
TTPOINT B904  42.657578  -71.364602


# For location at given bearing and distance from starting point.

TTVECTOR  B5bbbddd  37^55.37N  81^7.86W  0.01  mi

# For location specified by x, y coordinates.

TTGRID   Byyyxxx    37^50.00N  81^00.00W  37^59.99N  81^09.99W

# UTM location for Lowell-Dracut-Tyngsborough State Forest.

TTUTM  B6xxxyyy  19T  10  300000  4720000



# Location for the corral.

TTCORRAL   37^55.50N  81^7.00W  0^0.02N

# Compact messages - Fixed locations xx and object yyy where
#   	Object numbers 100 - 199	= bicycle
#	Object numbers 200 - 299	= fire truck
#	Others				= dog

TTMACRO  xx1yy  B9xx*AB166*AA2B4C5B3B0A1yy
TTMACRO  xx2yy  B9xx*AB170*AA3C4C7C3B0A2yy
TTMACRO  xxyyy  B9xx*AB180*AA3A6C4A0Ayyy

TTMACRO  z  Cz

# Receive on channel 0, Transmit object reports on channel 1 with optional via path.
# You probably want to put in a transmit delay on the APRStt channel so it
# it doesn't start sending a response before the user releases PTT.
# This is in 10 ms units so 100 means 1000 ms = 1 second.

#TTOBJ 0 1 WIDE1-1
#CHANNEL 0
#DWAIT 100

# Advertise gateway position with beacon.

# OBEACON DELAY=0:15 EVERY=10:00 VIA=WIDE1-1 OBJNAME=WB2OSZ-tt SYMBOL=APRStt LAT=42^37.14N LONG=71^20.83W COMMENT="APRStt Gateway"


# Sample speech responses.
# Default is Morse code "R" for received OK and "?" for all errors.

#TTERR  OK               SPEECH  Message Received.
#TTERR  D_MSG            SPEECH  D not implemented.
#TTERR  INTERNAL         SPEECH  Internal error.
#TTERR  MACRO_NOMATCH    SPEECH  No definition for digit sequence.
#TTERR  BAD_CHECKSUM     SPEECH  Bad checksum on call.
#TTERR  INVALID_CALL     SPEECH  Invalid callsign.
#TTERR  INVALID_OBJNAME  SPEECH  Invalid object name.
#TTERR  INVALID_SYMBOL   SPEECH  Invalid symbol.
#TTERR  INVALID_LOC      SPEECH  Invalid location.
#TTERR  NO_CALL          SPEECH  No call or object name.
#TTERR  SATSQ            SPEECH  Satellite square must be 4 digits.
#TTERR  SUFFIX_NO_CALL   SPEECH  Send full call before using suffix.