forked from Ultimaker/fdm_materials
-
Notifications
You must be signed in to change notification settings - Fork 0
/
generic_pc.xml.fdm_material
160 lines (145 loc) · 7 KB
/
generic_pc.xml.fdm_material
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
<?xml version="1.0" encoding="UTF-8"?>
<!--
Generic PC profile. The data in this file may not be correct for your specific machine.
-->
<fdmmaterial xmlns="http://www.ultimaker.com/material" xmlns:cura="http://www.ultimaker.com/cura" version="1.3">
<metadata>
<name>
<brand>Generic</brand>
<material>PC</material>
<color>Generic</color>
</name>
<GUID>98c05714-bf4e-4455-ba27-57d74fe331e4</GUID>
<version>31</version>
<color_code>#F29030</color_code>
<description>Strong, tough and temperature resistant. PC offers a great print quality, heat resistance up to 110ºC, mechanical strength and toughness.</description>
<adhesion_info>Use glue for small prints. An adhesion sheet is recommended for larger prints. Set your print speed to a low value (10mm/sec) to get better layer bonding.</adhesion_info>
</metadata>
<properties>
<density>1.19</density>
<diameter>2.85</diameter>
</properties>
<settings>
<!-- Deprime settings -->
<setting key="anti ooze retract position">-7</setting>
<setting key="anti ooze retract speed">50</setting>
<setting key="break preparation position">-16</setting>
<setting key="break preparation speed">50</setting>
<setting key="break preparation temperature">275</setting>
<setting key="break position">-50</setting>
<setting key="break speed">25</setting>
<setting key="break temperature">95</setting>
<setting key="pressure release dwell time">25</setting>
<setting key="dwell time before break preparation move">2</setting>
<setting key="end of print purge volume">0</setting>
<setting key="end of filament purge volume">0</setting>
<setting key="flush purge length">60</setting>
<!-- material station (un)loading settings -->
<setting key="maximum park duration">7200</setting>
<setting key="no load move factor">0.92</setting>
<!-- print settings -->
<setting key="print temperature">270</setting>
<setting key="standby temperature">170</setting>
<setting key="heated bed temperature">107</setting>
<setting key="build volume temperature">41</setting>
<setting key="adhesion tendency">0</setting>
<setting key="surface energy">65</setting>
<cura:setting key="material_shrinkage_percentage">100</cura:setting>
<!-- For material flow sensor -->
<setting key="relative extrusion">1.0</setting>
<setting key="flow sensor detection margin">0.8</setting>
<setting key="retract compensation">0</setting>
<machine>
<machine_identifier manufacturer="Ultimaker B.V." product="Ultimaker 2+"/>
<machine_identifier manufacturer="Ultimaker B.V." product="Ultimaker 2 Extended+"/>
<setting key="hardware compatible">yes</setting>
<hotend id="0.25 mm" />
<hotend id="0.4 mm" />
<hotend id="0.6 mm" />
<hotend id="0.8 mm" />
</machine>
<machine>
<machine_identifier manufacturer="Ultimaker B.V." product="Ultimaker 3"/>
<machine_identifier manufacturer="Ultimaker B.V." product="Ultimaker 3 Extended"/>
<hotend id="AA 0.25">
<setting key="hardware compatible">yes</setting>
<setting key="retraction amount">6.5</setting>
</hotend>
<hotend id="AA 0.4">
<setting key="hardware compatible">yes</setting>
<setting key="print cooling">0</setting>
<setting key="retraction amount">8</setting>
<setting key="retraction speed">35</setting>
</hotend>
<hotend id="AA 0.8">
<setting key="hardware compatible">yes</setting>
<setting key="print cooling">5</setting>
</hotend>
</machine>
<machine>
<machine_identifier manufacturer="Ultimaker B.V." product="Ultimaker 2+ Connect"/>
<setting key="print temperature">260</setting>
<setting key="hardware compatible">yes</setting>
<hotend id="0.25 mm" />
<hotend id="0.4 mm" />
<hotend id="0.6 mm" />
<hotend id="0.8 mm" />
</machine>
<machine>
<machine_identifier manufacturer="Ultimaker B.V." product="Ultimaker S3"/>
<setting key="heated bed temperature">110</setting>
<hotend id="AA 0.25">
<setting key="hardware compatible">yes</setting>
<setting key="retraction amount">6.5</setting>
</hotend>
<hotend id="AA 0.4">
<setting key="hardware compatible">yes</setting>
<setting key="print cooling">0</setting>
<setting key="retraction amount">8</setting>
</hotend>
<hotend id="AA 0.8">
<setting key="hardware compatible">yes</setting>
<setting key="print cooling">5</setting>
</hotend>
</machine>
<machine>
<machine_identifier manufacturer="Ultimaker B.V." product="Ultimaker S5"/>
<machine_identifier manufacturer="Ultimaker B.V." product="Ultimaker S7"/>
<setting key="heated bed temperature">110</setting>
<hotend id="AA 0.25">
<setting key="hardware compatible">yes</setting>
<setting key="retraction amount">6.5</setting>
</hotend>
<hotend id="AA 0.4">
<setting key="hardware compatible">yes</setting>
<setting key="print cooling">0</setting>
<setting key="retraction amount">8</setting>
</hotend>
<hotend id="AA 0.8">
<setting key="hardware compatible">yes</setting>
<setting key="retraction amount">8</setting>
<setting key="print cooling">5</setting>
</hotend>
</machine>
<machine>
<machine_identifier manufacturer="Cartesio bv" product="cartesio" />
<setting key="print cooling">0.0</setting>
<setting key="standby temperature">160</setting>
<setting key="retraction speed">40</setting>
<setting key="heated bed temperature">135</setting>
<setting key="print temperature">245</setting>
<hotend id="0.25mm thermoplastic extruder">
<setting key="hardware compatible">yes</setting>
<setting key="retraction amount">1.0</setting>
</hotend>
<hotend id="0.4mm thermoplastic extruder">
<setting key="hardware compatible">yes</setting>
<setting key="retraction amount">1.0</setting>
</hotend>
<hotend id="0.8mm thermoplastic extruder">
<setting key="hardware compatible">yes</setting>
<setting key="retraction amount">1.5</setting>
</hotend>
</machine>
</settings>
</fdmmaterial>