Skip to content

Commit

Permalink
Project Creation
Browse files Browse the repository at this point in the history
  • Loading branch information
@Xk-w
Xk-w authored Dec 20, 2023
1 parent 401532f commit 597217d
Show file tree
Hide file tree
Showing 20 changed files with 3,358 additions and 0 deletions.
123 changes: 123 additions & 0 deletions examples/Power/ETA4662/main.cpp
View file
Original file line number Diff line number Diff line change
@@ -0,0 +1,123 @@
/*
* @Description(CN):
* 基于Arduino_DriveBus库的ETA4662充电芯片例程
* 以下是使用该款芯片需要注意的几个点：
* 1. ETA4662默认状态下为关闭充电功能的状态，需要手动开启充电
* 2. 在使用Arduino_DriveBus库时，初始化阶段会对芯片进行一次初始化的写入数据，具体
* 初始化内容可以前往芯片文件下的XXX_Initialization_Operations[]这个数组查看
* 3. Arduino_DriveBus库使用枚举的方式寄存操作芯片的命令和值，具体的可执行命令已经在
* 芯片文件的@Description有说明
*
* @Description(EN):
* ETA4662 charging chip routine based on Arduino_DriveBus library
* Here are a few points to note when using this chip:
* 1. The ETA4662 is in a default state of disabling charging, which needs to be manually enabled.
* 2. When using the Arduino_DriveBus library, the chip is initialized during the initialization phase
* by writing data to it. The specific initialization content can be viewed in the XXX_Initialization_Operations[]
* array under the chip file.
* 3. The Arduino_DriveBus library uses enumerations to register commands and values for operating the chip.
* The specific executable commands are explained in the chip file under @Description.
*
* @version: V1.0.0
* @Author: Xk_w
* @Date: 2023-11-27 10:08:51
* @LastEditors: Xk_w
* @LastEditTime: 2023-11-27 17:54:02
* @License: GPL 3.0
*/
#include "Arduino_DriveBus_Library.h"
#include "pin_config.h"

std::shared_ptr<Arduino_IIC_DriveBus> IIC_Bus =
std::make_shared<Arduino_HWIIC>(IIC_SDA, IIC_SCL, &Wire);

std::unique_ptr<Arduino_IIC> ETA4662(new Arduino_ETA4662(IIC_Bus, ETA4662_DEVICE_ADDRESS,
DRIVEBUS_DEFAULT_VALUE, DRIVEBUS_DEFAULT_VALUE));

void setup()
{
Serial.begin(115200);
Serial.println("Ciallo");

while (ETA4662->begin() == false)
{
Serial.println("ETA4662 initialization fail");
delay(2000);
}
Serial.println("ETA4662 initialization successfully");

ETA4662->IIC_Write_Device_State(ETA4662->Arduino_IIC_Power::Device::POWER_DEVICE_CHARGING_MODE,
ETA4662->Arduino_IIC_Power::Device_State::POWER_DEVICE_ON); // 充电
// ETA4662->IIC_Write_Device_State(ETA4662->Arduino_IIC_Power::Device::POWER_DEVICE_WATCHDOG_MODE,
// ETA4662->Arduino_IIC_Power::Device_State::POWER_DEVICE_ON); // 看门狗（当启动ETA4662的看门狗时，看门狗的定时器到达指定值后将断开电源重新连接，与ETA4662通信的MCU将重启）
// ETA4662->IIC_Write_Device_Value(ETA4662->Arduino_IIC_Power::Device_Value::POWER_DEVICE_WATCHDOG_TIMER, 80); // 看门狗定时器值

// 热调节阈值设置为60度
ETA4662->IIC_Write_Device_Value(ETA4662->Arduino_IIC_Power::Device_Value::POWER_DEVICE_THERMAL_REGULATION_THRESHOLD, 60);
// 最小输入电压设置为4760mV
ETA4662->IIC_Write_Device_Value(ETA4662->Arduino_IIC_Power::Device_Value::POWER_DEVICE_MINIMUM_INPUT_VOLTAGE_LIMIT, 4760);
// 充电目标电压电压设置为4215mV
ETA4662->IIC_Write_Device_Value(ETA4662->Arduino_IIC_Power::Device_Value::POWER_DEVICE_CHARGING_TARGET_VOLTAGE_LIMIT, 4215);
// 系统电压设置为4950mV（输出电压）
ETA4662->IIC_Write_Device_Value(ETA4662->Arduino_IIC_Power::Device_Value::POWER_DEVICE_SYSTEM_VOLTAGE_LIMIT, 4950);
// 输入电流限制设置为470mA
ETA4662->IIC_Write_Device_Value(ETA4662->Arduino_IIC_Power::Device_Value::POWER_DEVICE_INPUT_CURRENT_LIMIT, 470);
// 快速充电电流限制设置为136mA
ETA4662->IIC_Write_Device_Value(ETA4662->Arduino_IIC_Power::Device_Value::POWER_DEVICE_FAST_CHARGING_CURRENT_LIMIT, 136);
// 终端充电和预充电电流限制设置为5mA
ETA4662->IIC_Write_Device_Value(ETA4662->Arduino_IIC_Power::Device_Value::POWER_DEVICE_TERMINATION_PRECHARGE_CHARGING_CURRENT_LIMIT, 5);
// BAT到SYS的放电电流限制设置为2200mA
ETA4662->IIC_Write_Device_Value(ETA4662->Arduino_IIC_Power::Device_Value::POWER_DEVICE_BAT_TO_SYS_DISCHARGE_CURRENT_LIMIT, 2200);
}
void loop()
{
Serial.printf("--------------------ETA4662--------------------\n");
Serial.printf("System running time: %d\n\n", (uint32_t)millis() / 1000);
Serial.printf("IIC_Bus.use_count(): %d\n\n", (int32_t)IIC_Bus.use_count());

Serial.printf("ID: %#X \n", (int32_t)ETA4662->IIC_Read_Device_ID());

Serial.printf("\nCharging Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_CHARGING_STATUS)).c_str());
Serial.printf("Input Source Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_INPUT_SOURCE_STATUS)).c_str());
Serial.printf("System Voltage Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_SYSTEM_VOLTAGE_STATUS)).c_str());
Serial.printf("Thermal Regulation Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_THERMAL_REGULATION_STATUS)).c_str());

Serial.printf("\nWatchdog Fault Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_WATCHDOG_FAULT_STATUS)).c_str());
Serial.printf("Input Fault Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_INPUT_FAULT_STATUS)).c_str());
Serial.printf("Thermal Shutdown Fault Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_THERMAL_SHUTDOWN_FAULT_STATUS)).c_str());
Serial.printf("Battery Fault Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_BATTERY_FAULT_STATUS)).c_str());
Serial.printf("Safety Timer Fault Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_SAFETY_TIMER_STATUS_FAULT_STATUS)).c_str());
Serial.printf("NTC Fault Status: %s \n",
(ETA4662->IIC_Read_Device_State(ETA4662->Arduino_IIC_Power::Status_Information::POWER_NTC_FAULT_STATUS)).c_str());

Serial.printf("\nThermal Regulation Threshold: %d ^C \n",
ETA4662->IIC_Read_Device_Value(ETA4662->Arduino_IIC_Power::Value_Information::POWER_THERMAL_REGULATION_THRESHOLD));

Serial.printf("\nInput Minimum Voltage Limit: %d mV \n",
ETA4662->IIC_Read_Device_Value(ETA4662->Arduino_IIC_Power::Value_Information::POWER_MINIMUM_INPUT_VOLTAGE_LIMIT));
Serial.printf("Charging Voltage Limit: %d mV \n",
ETA4662->IIC_Read_Device_Value(ETA4662->Arduino_IIC_Power::Value_Information::POWER_CHARGING_TARGET_VOLTAGE_LIMIT));
Serial.printf("System Voltage Limit: %d mV \n",
ETA4662->IIC_Read_Device_Value(ETA4662->Arduino_IIC_Power::Value_Information::POWER_SYSTEM_VOLTAGE_LIMIT));
Serial.printf("Input Current Limit: %d mA \n",
ETA4662->IIC_Read_Device_Value(ETA4662->Arduino_IIC_Power::Value_Information::POWER_INPUT_CURRENT_LIMIT));
Serial.printf("Fast Charge Current Limit: %d mA \n",
ETA4662->IIC_Read_Device_Value(ETA4662->Arduino_IIC_Power::Value_Information::POWER_FAST_CHARGING_CURRENT_LIMIT));
Serial.printf("Termination And Precondition Charge Current Limit: %d mA \n",
ETA4662->IIC_Read_Device_Value(ETA4662->Arduino_IIC_Power::Value_Information::POWER_TERMINATION_PRECHARGE_CHARGING_CURRENT_LIMIT));
Serial.printf("BAT To SYS Discharge Current Limit: %d mA \n",
ETA4662->IIC_Read_Device_Value(ETA4662->Arduino_IIC_Power::Value_Information::POWER_BAT_TO_SYS_DISCHARGE_CURRENT_LIMIT));

Serial.printf("--------------------ETA4662--------------------\n");

delay(1000);
}
160 changes: 160 additions & 0 deletions examples/Power/SY6970/main.cpp
View file
Original file line number Diff line number Diff line change
@@ -0,0 +1,160 @@
/*
* @Description(CN):
* 基于Arduino_DriveBus库的SY6970充电芯片例程
* 以下是使用该款芯片需要注意的几个点：
* 1. SY6970在获取芯片电压电流的时候需要开启ADC测量功能才能正常检测到电压电流等数据
* 如果未开启则获得的是错误信息
* 2. 在使用Arduino_DriveBus库时，初始化阶段会对芯片进行一次初始化的写入数据，具体
* 初始化内容可以前往芯片文件下的XXX_Initialization_Operations[]这个数组查看
* 3. Arduino_DriveBus库使用枚举的方式寄存操作芯片的命令和值，具体的可执行命令已经在
* 芯片文件的@Description有说明
*
* @Description(EN):
* SY6970 Charging Chip Routine based on Arduino_DriveBus Library
* Here are a few points to note when using this chip:
* 1. When obtaining voltage and current data from the SY6970 chip, the ADC measurement
* function must be enabled to correctly detect the voltage, current, and other data. If not enabled,
* error messages will be obtained.
* 2. When using the Arduino_DriveBus library, the chip is initialized with data during the initialization
* phase. The specific initialization content can be viewed in the XXX_Initialization_Operations[] array in
* the chip file.
* 3. The Arduino_DriveBus library uses enumerations to register commands and values for operating
* the chip. The specific executable commands are explained in the chip file under @Description.
*
* @version: V1.0.0
* @Author: Xk_w
* @Date: 2023-11-17 13:34:38
* @LastEditors: Xk_w
* @LastEditTime: 2023-11-27 17:33:55
* @License: GPL 3.0
*/
#include "Arduino_DriveBus_Library.h"
#include "pin_config.h"

std::shared_ptr<Arduino_IIC_DriveBus> IIC_Bus =
std::make_shared<Arduino_HWIIC>(IIC_SDA, IIC_SCL, &Wire);

std::unique_ptr<Arduino_IIC> SY6970(new Arduino_SY6970(IIC_Bus, SY6970_DEVICE_ADDRESS,
DRIVEBUS_DEFAULT_VALUE, DRIVEBUS_DEFAULT_VALUE));

static bool Temp1 = 0;

void setup()
{
Serial.begin(115200);
Serial.println("Ciallo");

while (SY6970->begin() == false)
{
Serial.println("SY6970 initialization fail");
delay(2000);
}
Serial.println("SY6970 initialization successfully");

// 开启ADC测量功能
while (SY6970->IIC_Write_Device_State(SY6970->Device::POWER_DEVICE_ADC_MEASURE,
SY6970->Device_State::POWER_DEVICE_ON) == false)
{
Serial.println("SY6970 ADC Measure ON fail");
delay(2000);
}
Serial.println("SY6970 ADC Measure ON successfully");

// 禁用看门狗定时器喂狗功能
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_WATCHDOG_TIMER, 0);
// 热调节阈值设置为60度
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_THERMAL_REGULATION_THRESHOLD, 60);
// 充电目标电压电压设置为4224mV
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_CHARGING_TARGET_VOLTAGE_LIMIT, 4224);
// 最小系统电压限制为3600mA
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_MINIMUM_SYSTEM_VOLTAGE_LIMIT, 3600);
// 设置OTG电压为5062mV
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_OTG_VOLTAGE_LIMIT, 5062);
// 输入电流限制设置为600mA
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_INPUT_CURRENT_LIMIT, 600);
// 快速充电电流限制设置为2112mA
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_FAST_CHARGING_CURRENT_LIMIT, 2112);
// 预充电电流限制设置为192mA
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_PRECHARGE_CHARGING_CURRENT_LIMIT, 192);
// 终端充电电流限制设置为320mA
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_TERMINATION_CHARGING_CURRENT_LIMIT, 320);
// OTG电流限制设置为500mA
SY6970->IIC_Write_Device_Value(SY6970->Arduino_IIC_Power::Device_Value::POWER_DEVICE_OTG_CHARGING_LIMIT, 500);
}

void loop()
{
Serial.printf("--------------------SY6970--------------------\n");
Serial.printf("System running time: %d\n\n", (uint32_t)millis() / 1000);
Serial.printf("IIC_Bus.use_count(): %d\n\n", (int32_t)IIC_Bus.use_count());

Serial.printf("IIC device ID: %#X \n", (int32_t)SY6970->IIC_Read_Device_ID());

Serial.printf("\nBUS Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_BUS_STATUS)).c_str());
Serial.printf("BUS Connection Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_BUS_CONNECTION_STATUS)).c_str());
Serial.printf("Charging Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_CHARGING_STATUS)).c_str());
Serial.printf("Input Source Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_INPUT_SOURCE_STATUS)).c_str());
Serial.printf("Input USB Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_INPUT_USB_STATUS)).c_str());
Serial.printf("System Voltage Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_SYSTEM_VOLTAGE_STATUS)).c_str());
Serial.printf("Thermal Regulation Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_THERMAL_REGULATION_STATUS)).c_str());

Serial.printf("\nWatchdog Fault Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_WATCHDOG_FAULT_STATUS)).c_str());
Serial.printf("OTG Fault Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_OTG_FAULT_STATUS)).c_str());
Serial.printf("Charging Fault Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_CHARGING_FAULT_STATUS)).c_str());
Serial.printf("Battery Fault Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_BATTERY_FAULT_STATUS)).c_str());
Serial.printf("NTC Fault Status: %s \n",
(SY6970->IIC_Read_Device_State(SY6970->Arduino_IIC_Power::Status_Information::POWER_NTC_FAULT_STATUS)).c_str());

Serial.printf("\nInput Voltage: %d mV \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_INPUT_VOLTAGE));
Serial.printf("Battery Voltage: %d mV \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_BATTERY_VOLTAGE));
Serial.printf("System Voltage: %d mV \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_SYSTEM_VOLTAGE));
Serial.printf("NTC Voltage Percentage: %.03f %% \n",
(float)SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_NTC_VOLTAGE_PERCENTAGE) / 1000.0);
Serial.printf("Charging Current: %d mA \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_CHARGING_CURRENT));
Serial.printf("Thermal Regulation Threshold: %d ^C \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_THERMAL_REGULATION_THRESHOLD));

Serial.printf("\nCharging Voltage Limit: %d mV \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_CHARGING_TARGET_VOLTAGE_LIMIT));
Serial.printf("Minimum System Voltage Limit: %d mV \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_MINIMUM_SYSTEM_VOLTAGE_LIMIT));
Serial.printf("OTG Voltage Limit: %d mV \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_OTG_VOLTAGE_LIMIT));
Serial.printf("Input Current Limit: %d mA \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_INPUT_CURRENT_LIMIT));
Serial.printf("Fast Charge Current Limit: %d mA \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_FAST_CHARGING_CURRENT_LIMIT));
Serial.printf("Precharge Charge Current Limit: %d mA \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_PRECHARGE_CHARGING_CURRENT_LIMIT));
Serial.printf("Termination Charge Current Limit: %d mA \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_TERMINATION_CHARGING_CURRENT_LIMIT));
Serial.printf("OTG Current Limit: %d mA \n",
SY6970->IIC_Read_Device_Value(SY6970->Arduino_IIC_Power::Value_Information::POWER_OTG_CURRENT_LIMIT));

Serial.printf("--------------------SY6970--------------------\n\n");

delay(1000);

Temp1 = !Temp1;
if (Temp1 == 0)
{
}
else
{
}
}
Loading

0 comments on commit 597217d

Please sign in to comment.