diff --git a/generic_cpe.xml.fdm_material b/generic_cpe.xml.fdm_material
index 4bb81b6a4..1e42c2f6a 100644
--- a/generic_cpe.xml.fdm_material
+++ b/generic_cpe.xml.fdm_material
@@ -155,6 +155,7 @@ Generic CPE profile. The data in this file may not be correct for your specific
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/generic_cpe_plus.xml.fdm_material b/generic_cpe_plus.xml.fdm_material
index 73ff30293..218b5d3a0 100644
--- a/generic_cpe_plus.xml.fdm_material
+++ b/generic_cpe_plus.xml.fdm_material
@@ -143,6 +143,7 @@ Generic CPE+ profile. The data in this file may not be correct for your specific
             <setting key="anti ooze retract position">-4</setting>
             <setting key="break preparation position">-12</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.4</cura:setting>
             <hotend id="AA 0.4">
                 <setting key="hardware compatible">yes</setting>
diff --git a/generic_nylon.xml.fdm_material b/generic_nylon.xml.fdm_material
index 2fc2c9b06..f525a880f 100644
--- a/generic_nylon.xml.fdm_material
+++ b/generic_nylon.xml.fdm_material
@@ -161,7 +161,7 @@ Generic Nylon profile. The data in this file may not be correct for your specifi
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">75</setting>
-            <setting key="retraction amount">1.5</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="anti ooze retract position">-6</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.4</cura:setting>
diff --git a/generic_petg.xml.fdm_material b/generic_petg.xml.fdm_material
index 49865f52b..fa2a057d3 100644
--- a/generic_petg.xml.fdm_material
+++ b/generic_petg.xml.fdm_material
@@ -142,6 +142,7 @@ Generic PETG profile. The data in this file may not be correct for your specific
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/generic_pp.xml.fdm_material b/generic_pp.xml.fdm_material
index 9dd712ad2..bf4ad627d 100644
--- a/generic_pp.xml.fdm_material
+++ b/generic_pp.xml.fdm_material
@@ -167,6 +167,7 @@ Generic Polypropylene profile. Serves as an example file, data in this file is n
             <setting key="anti ooze retract position">-14</setting>
             <setting key="break preparation position">-14</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.7</cura:setting>
             <setting key="flow sensor detection margin">0.2</setting>
 
diff --git a/generic_tpu.xml.fdm_material b/generic_tpu.xml.fdm_material
index d2bfe5995..ad7ec74f7 100644
--- a/generic_tpu.xml.fdm_material
+++ b/generic_tpu.xml.fdm_material
@@ -146,7 +146,7 @@ Generic TPU 95A profile. The data in this file may not be correct for your speci
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">50</setting>
-            <setting key="retraction amount">2</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="break position">-50</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.3</cura:setting>
diff --git a/ultimaker_absr_175.xml.fdm_material b/ultimaker_absr_175.xml.fdm_material
index 22d6e9c8b..a6b6566fc 100644
--- a/ultimaker_absr_175.xml.fdm_material
+++ b/ultimaker_absr_175.xml.fdm_material
@@ -8,7 +8,7 @@
         </name>
         <GUID>88c8919c-6a09-471a-b7b6-e801263d862d</GUID>
         <reference_material_id>abs-wss1</reference_material_id>
-        <version>7</version>
+        <version>8</version>
         <color_code>#8cb219</color_code>
         <description>Tough and durable. ABS is good for mechanical parts. It is impact resistant, dimensionally stable and handles temperatures up to 85ºC.</description>
         <adhesion_info>No glue needed</adhesion_info>
@@ -55,6 +55,7 @@
             <machine_identifier manufacturer="Ultimaker B.V." product="UltiMaker Method XL" />
             <setting key="build volume temperature">85</setting>
             <setting key="heated bed temperature">95</setting>
+            <cura:setting key="material_bed_temperature_layer_0">100</cura:setting>
             <hotend id="1A">
                 <setting key="hardware compatible">no</setting>
             </hotend>
diff --git a/ultimaker_asa_175.xml.fdm_material b/ultimaker_asa_175.xml.fdm_material
index d7041e8ad..5414263c5 100644
--- a/ultimaker_asa_175.xml.fdm_material
+++ b/ultimaker_asa_175.xml.fdm_material
@@ -8,7 +8,7 @@
         </name>
         <GUID>f79bc612-21eb-482e-ad6c-87d75bdde066</GUID>
         <reference_material_id>asa</reference_material_id>
-        <version>5</version>
+        <version>6</version>
         <color_code>#f1ece1</color_code>
         <description>ASA combines the qualities of ABS with the added benefit of UV resistance and additional moisture resistance making it ideal for equipment exposed to sunlight and rain over long periods of time – such as products for the agriculture, transportation, and power and utility industries.</description>
         <adhesion_info>No glue needed</adhesion_info>
@@ -31,8 +31,7 @@
             <machine_identifier manufacturer="Ultimaker B.V." product="UltiMaker Method X" />
             <setting key="print temperature">255</setting>
             <setting key="standby temperature">190</setting>
-            <setting key="build volume temperature">93</setting>
-            <setting key="heated bed temperature">95</setting>
+            <setting key="build volume temperature">107</setting>
             <cura:setting key="material_shrinkage_percentage">100.44</cura:setting>
             <cura:setting key="material_shrinkage_percentage_z">100.6</cura:setting>
 
diff --git a/ultimaker_cpe.xml.fdm_material b/ultimaker_cpe.xml.fdm_material
index 20bdc85f4..39e40bde8 100644
--- a/ultimaker_cpe.xml.fdm_material
+++ b/ultimaker_cpe.xml.fdm_material
@@ -156,6 +156,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_black.xml.fdm_material b/ultimaker_cpe_black.xml.fdm_material
index fadf630d6..7c65f21ff 100644
--- a/ultimaker_cpe_black.xml.fdm_material
+++ b/ultimaker_cpe_black.xml.fdm_material
@@ -154,6 +154,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_blue.xml.fdm_material b/ultimaker_cpe_blue.xml.fdm_material
index 8b7601cb2..18f5c9eed 100644
--- a/ultimaker_cpe_blue.xml.fdm_material
+++ b/ultimaker_cpe_blue.xml.fdm_material
@@ -154,6 +154,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_dark-grey.xml.fdm_material b/ultimaker_cpe_dark-grey.xml.fdm_material
index 5b9387ec1..4fb493c9b 100644
--- a/ultimaker_cpe_dark-grey.xml.fdm_material
+++ b/ultimaker_cpe_dark-grey.xml.fdm_material
@@ -154,6 +154,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_green.xml.fdm_material b/ultimaker_cpe_green.xml.fdm_material
index 15db3a6ce..210973531 100644
--- a/ultimaker_cpe_green.xml.fdm_material
+++ b/ultimaker_cpe_green.xml.fdm_material
@@ -154,6 +154,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_light-grey.xml.fdm_material b/ultimaker_cpe_light-grey.xml.fdm_material
index f016db7c9..71c6a8eab 100644
--- a/ultimaker_cpe_light-grey.xml.fdm_material
+++ b/ultimaker_cpe_light-grey.xml.fdm_material
@@ -154,6 +154,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_plus.xml.fdm_material b/ultimaker_cpe_plus.xml.fdm_material
index 5888a1d98..572531cbb 100644
--- a/ultimaker_cpe_plus.xml.fdm_material
+++ b/ultimaker_cpe_plus.xml.fdm_material
@@ -144,6 +144,7 @@
             <setting key="anti ooze retract position">-4</setting>
             <setting key="break preparation position">-12</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.4</cura:setting>
             <hotend id="AA 0.4">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_plus_black.xml.fdm_material b/ultimaker_cpe_plus_black.xml.fdm_material
index 983a99045..f7eeefec3 100644
--- a/ultimaker_cpe_plus_black.xml.fdm_material
+++ b/ultimaker_cpe_plus_black.xml.fdm_material
@@ -142,6 +142,7 @@
             <setting key="anti ooze retract position">-4</setting>
             <setting key="break preparation position">-12</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.4</cura:setting>
             <hotend id="AA 0.4">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_plus_transparent.xml.fdm_material b/ultimaker_cpe_plus_transparent.xml.fdm_material
index 0da308805..fc182f6c8 100644
--- a/ultimaker_cpe_plus_transparent.xml.fdm_material
+++ b/ultimaker_cpe_plus_transparent.xml.fdm_material
@@ -142,6 +142,7 @@
             <setting key="anti ooze retract position">-4</setting>
             <setting key="break preparation position">-12</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.4</cura:setting>
             <hotend id="AA 0.4">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_plus_white.xml.fdm_material b/ultimaker_cpe_plus_white.xml.fdm_material
index d34716ef7..35e05372a 100644
--- a/ultimaker_cpe_plus_white.xml.fdm_material
+++ b/ultimaker_cpe_plus_white.xml.fdm_material
@@ -142,6 +142,7 @@
             <setting key="anti ooze retract position">-4</setting>
             <setting key="break preparation position">-12</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.4</cura:setting>
             <hotend id="AA 0.4">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_red.xml.fdm_material b/ultimaker_cpe_red.xml.fdm_material
index 378f52cea..3d69b5908 100644
--- a/ultimaker_cpe_red.xml.fdm_material
+++ b/ultimaker_cpe_red.xml.fdm_material
@@ -154,6 +154,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_transparent.xml.fdm_material b/ultimaker_cpe_transparent.xml.fdm_material
index d3553e26c..3154f4faf 100644
--- a/ultimaker_cpe_transparent.xml.fdm_material
+++ b/ultimaker_cpe_transparent.xml.fdm_material
@@ -154,6 +154,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_white.xml.fdm_material b/ultimaker_cpe_white.xml.fdm_material
index b50b3d7f6..b5197cb60 100644
--- a/ultimaker_cpe_white.xml.fdm_material
+++ b/ultimaker_cpe_white.xml.fdm_material
@@ -154,6 +154,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_cpe_yellow.xml.fdm_material b/ultimaker_cpe_yellow.xml.fdm_material
index b3e635fe1..8b3b523cc 100644
--- a/ultimaker_cpe_yellow.xml.fdm_material
+++ b/ultimaker_cpe_yellow.xml.fdm_material
@@ -154,6 +154,7 @@
             <setting key="anti ooze retract position">-18</setting>
             <setting key="break preparation position">-18</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
             <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_nylon.xml.fdm_material b/ultimaker_nylon.xml.fdm_material
index 7e402d9fc..144094712 100644
--- a/ultimaker_nylon.xml.fdm_material
+++ b/ultimaker_nylon.xml.fdm_material
@@ -162,7 +162,7 @@
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">75</setting>
-            <setting key="retraction amount">1.5</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="anti ooze retract position">-6</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.4</cura:setting>
diff --git a/ultimaker_nylon_black.xml.fdm_material b/ultimaker_nylon_black.xml.fdm_material
index 9d726e6cf..63bec3660 100644
--- a/ultimaker_nylon_black.xml.fdm_material
+++ b/ultimaker_nylon_black.xml.fdm_material
@@ -160,7 +160,7 @@
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">75</setting>
-            <setting key="retraction amount">1.5</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="anti ooze retract position">-6</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.4</cura:setting>
diff --git a/ultimaker_nylon_transparent.xml.fdm_material b/ultimaker_nylon_transparent.xml.fdm_material
index 81a5089b7..8c87e94ba 100644
--- a/ultimaker_nylon_transparent.xml.fdm_material
+++ b/ultimaker_nylon_transparent.xml.fdm_material
@@ -160,7 +160,7 @@
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">75</setting>
-            <setting key="retraction amount">1.5</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="anti ooze retract position">-6</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.4</cura:setting>
diff --git a/ultimaker_petg.xml.fdm_material b/ultimaker_petg.xml.fdm_material
index a8ec25761..91063c8ae 100644
--- a/ultimaker_petg.xml.fdm_material
+++ b/ultimaker_petg.xml.fdm_material
@@ -143,6 +143,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_black.xml.fdm_material b/ultimaker_petg_black.xml.fdm_material
index 83e2765d9..416fb0590 100644
--- a/ultimaker_petg_black.xml.fdm_material
+++ b/ultimaker_petg_black.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_blue.xml.fdm_material b/ultimaker_petg_blue.xml.fdm_material
index 1a3c30ba9..ebfdc52c9 100644
--- a/ultimaker_petg_blue.xml.fdm_material
+++ b/ultimaker_petg_blue.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_blue_translucent.xml.fdm_material b/ultimaker_petg_blue_translucent.xml.fdm_material
index 58ef9f782..a1b5545c2 100644
--- a/ultimaker_petg_blue_translucent.xml.fdm_material
+++ b/ultimaker_petg_blue_translucent.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_green.xml.fdm_material b/ultimaker_petg_green.xml.fdm_material
index 7134033ae..439bbb2bc 100644
--- a/ultimaker_petg_green.xml.fdm_material
+++ b/ultimaker_petg_green.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_green_translucent.xml.fdm_material b/ultimaker_petg_green_translucent.xml.fdm_material
index cc4e85e90..2332cb2e1 100644
--- a/ultimaker_petg_green_translucent.xml.fdm_material
+++ b/ultimaker_petg_green_translucent.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_grey.xml.fdm_material b/ultimaker_petg_grey.xml.fdm_material
index 0f59e18aa..d037b23d9 100644
--- a/ultimaker_petg_grey.xml.fdm_material
+++ b/ultimaker_petg_grey.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_orange.xml.fdm_material b/ultimaker_petg_orange.xml.fdm_material
index fc5aa6040..6f3e8797d 100644
--- a/ultimaker_petg_orange.xml.fdm_material
+++ b/ultimaker_petg_orange.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_red.xml.fdm_material b/ultimaker_petg_red.xml.fdm_material
index b0b33f227..078b7e797 100644
--- a/ultimaker_petg_red.xml.fdm_material
+++ b/ultimaker_petg_red.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_red_translucent.xml.fdm_material b/ultimaker_petg_red_translucent.xml.fdm_material
index 1aeea4243..1b0f61961 100644
--- a/ultimaker_petg_red_translucent.xml.fdm_material
+++ b/ultimaker_petg_red_translucent.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_silver.xml.fdm_material b/ultimaker_petg_silver.xml.fdm_material
index 179527983..e225e7447 100644
--- a/ultimaker_petg_silver.xml.fdm_material
+++ b/ultimaker_petg_silver.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_transparent.xml.fdm_material b/ultimaker_petg_transparent.xml.fdm_material
index c68ad72e8..f54744170 100644
--- a/ultimaker_petg_transparent.xml.fdm_material
+++ b/ultimaker_petg_transparent.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_white.xml.fdm_material b/ultimaker_petg_white.xml.fdm_material
index 096dfd471..cc76c2ff5 100644
--- a/ultimaker_petg_white.xml.fdm_material
+++ b/ultimaker_petg_white.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_yellow.xml.fdm_material b/ultimaker_petg_yellow.xml.fdm_material
index a123dc17f..d22aa2435 100644
--- a/ultimaker_petg_yellow.xml.fdm_material
+++ b/ultimaker_petg_yellow.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_petg_yellow_fluorescent.xml.fdm_material b/ultimaker_petg_yellow_fluorescent.xml.fdm_material
index 2e0154e17..ed302a528 100644
--- a/ultimaker_petg_yellow_fluorescent.xml.fdm_material
+++ b/ultimaker_petg_yellow_fluorescent.xml.fdm_material
@@ -141,6 +141,7 @@
             <setting key="print cooling">50</setting>
             <setting key="heated bed temperature">85</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.2</cura:setting>
            <hotend id="AA 0.25">
                 <setting key="hardware compatible">yes</setting>
diff --git a/ultimaker_pp_transparent.xml.fdm_material b/ultimaker_pp_transparent.xml.fdm_material
index 6b4be78ba..28c257245 100644
--- a/ultimaker_pp_transparent.xml.fdm_material
+++ b/ultimaker_pp_transparent.xml.fdm_material
@@ -166,6 +166,7 @@
             <setting key="anti ooze retract position">-14</setting>
             <setting key="break preparation position">-14</setting>
             <setting key="no load move factor">1</setting>
+            <setting key="retraction amount">5</setting>
             <cura:setting key="material_shrinkage_percentage">100.7</cura:setting>
             <setting key="flow sensor detection margin">0.2</setting>
 
diff --git a/ultimaker_tpu.xml.fdm_material b/ultimaker_tpu.xml.fdm_material
index 2b323951d..1be8ebd34 100644
--- a/ultimaker_tpu.xml.fdm_material
+++ b/ultimaker_tpu.xml.fdm_material
@@ -147,7 +147,7 @@
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">50</setting>
-            <setting key="retraction amount">2</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="break position">-50</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.3</cura:setting>
diff --git a/ultimaker_tpu_black.xml.fdm_material b/ultimaker_tpu_black.xml.fdm_material
index de0bdeda3..ae87b1cb1 100644
--- a/ultimaker_tpu_black.xml.fdm_material
+++ b/ultimaker_tpu_black.xml.fdm_material
@@ -145,7 +145,7 @@
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">50</setting>
-            <setting key="retraction amount">2</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="break position">-50</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.3</cura:setting>
diff --git a/ultimaker_tpu_blue.xml.fdm_material b/ultimaker_tpu_blue.xml.fdm_material
index 20ff1802d..c5a460c97 100644
--- a/ultimaker_tpu_blue.xml.fdm_material
+++ b/ultimaker_tpu_blue.xml.fdm_material
@@ -145,7 +145,7 @@
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">50</setting>
-            <setting key="retraction amount">2</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="break position">-50</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.3</cura:setting>
diff --git a/ultimaker_tpu_red.xml.fdm_material b/ultimaker_tpu_red.xml.fdm_material
index 59d560e01..de0ecdee3 100644
--- a/ultimaker_tpu_red.xml.fdm_material
+++ b/ultimaker_tpu_red.xml.fdm_material
@@ -145,7 +145,7 @@
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">50</setting>
-            <setting key="retraction amount">2</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="break position">-50</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.3</cura:setting>
diff --git a/ultimaker_tpu_white.xml.fdm_material b/ultimaker_tpu_white.xml.fdm_material
index e7807d31e..4d0b6bb62 100644
--- a/ultimaker_tpu_white.xml.fdm_material
+++ b/ultimaker_tpu_white.xml.fdm_material
@@ -145,7 +145,7 @@
             <setting key="heated bed temperature">40</setting>
             <setting key="build volume temperature">30</setting>
             <setting key="print cooling">50</setting>
-            <setting key="retraction amount">2</setting>
+            <setting key="retraction amount">5</setting>
             <setting key="break position">-50</setting>
             <setting key="no load move factor">1</setting>
             <cura:setting key="material_shrinkage_percentage">100.3</cura:setting>